Honeywell ADEMCO LYNXR-I Security System Скачать руководство пользователя страница 25

Страница: 25 / 72

LYNXR-I Installation and Setup Guide

- 25 -

Data Field Descriptions

✻

Low Battery Report Code

(See notes above)

This will be sent when a low battery condition exists in the
system’s standby battery.

✻

Test Report Code

(See notes above)

This is sent periodically to test that the communicator and
phone lines are operational (frequency of report is selected in
field

✻

51).

✻

Open Report Code
(See notes above)

This is sent upon disarming of the system. 2nd digit = user
number, if expanded or 4+2 reporting is selected.

✻

Arm AWAY/STAY Report Code

(See notes above)

This option allows for independent programming of AWAY and
STAY reports. 2nd digit of report is user number if expanded or
4+2 reporting is selected.

NOTE: OPEN reports are not sent if the associated closing
report is not enabled.

✻

RF transmitter Low Batt. Report Code

(See notes above)

This is sent in the event that a wireless transmitter low battery
condition exists.

✻

Cancel Report Code

(See notes above)

This is sent upon disarming of the system after an alarm
condition was reported.

RESTORE REPORT CODES (

✻

70–

✻

76)

✻

Alarm Restore Report Code, 1st Digit

(See notes above)

Sent when the zone that caused an alarm is restored to its non-
faulted condition. 2nd digit is automatically sent as the 2nd digit
of the zone alarm report code programmed in field

✻

56, if

expanded or 4+2 reporting is selected.

✻

Trouble Restore Report Code

(See notes above)

Sent when a trouble in a zone is restored.

✻

Bypass Restore Report Code

(See notes above)

Sent when a zone that has been bypassed is unbypassed.

✻

AC Restore Report Code

(See notes above)

Sent when AC power has been restored after an AC power
outage.

✻

Low Battery Restore Report Code

(See notes above)

Sent when a system low battery condition is restored to normal.

✻

RF Transmitter Low Batt. Restore Code

(See notes above)

Sent when a transmitter that previously sent in a “low battery” message
has sent a message indicating it no longer has a low battery condition.

✻

Test Restore Report Code

(See notes above)

Sent when the test mode is exited. A restore code entered here will cause
a restore message to be sent when Test mode is exited.

Содержание ADEMCO LYNXR-I Security System









































































Результаты поиска

Содержание ADEMCO LYNXR-I Security System

Отзывы:

Honeywell ADEMCO LYNXR-I Security System, Инструкция по установке и настройке, Страница: 25 / 72

Результаты поиска

Содержание ADEMCO LYNXR-I Security System

Отзывы: