Honeywell ADEMCO LYNXR-EN Скачать руководство пользователя | Manualshive

Страница: 49 / 64

background image

– 49 –

UL NOTICE: This is a "Grade A" residential system.

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.

Federal Communications Commission (FCC) Part 15 Statement

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC
requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is,
in strict accordance with the manufacturer's instructions, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class B computing device in
accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•  If using an indoor antenna, have a quality outdoor antenna installed.
•  Reorient the receiving antenna until interference is reduced or eliminated.
•  Move the radio or television receiver away from the receiver/control.
•  Move the antenna leads away from any wire runs to the receiver/control.
•  Plug the receiver/control into a different outlet so that it and the radio or television receiver are on

different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user or installer may find the following booklet prepared by the Federal Communications
Commission helpful: "Interference Handbook." This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the
Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's
authority to operate the equipment.

Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

«
...
47
48
49
50
51
...
»

Содержание ADEMCO LYNXR-EN

































































Отзывы:

Нет отзывов

Похожие инструкции для ADEMCO LYNXR-EN

Бренд: DW Страницы: 32

Бренд: Rae Страницы: 49

Бренд: UbiBot Страницы: 11

Бренд: EVE Страницы: 43

UTILITY UTAC13-0

Бренд: WIA Страницы: 8

Бренд: ACTi Страницы: 2

Picomig 305 D2 puls

Бренд: EWM Страницы: 84

Бренд: Abicor Binzel Страницы: 2

KNC-p3DR28V12IR

Бренд: OMNI-IP Страницы: 36

Бренд: Pyle Страницы: 6

Бренд: Serenity Страницы: 3

E-ACVDRLY Series

Бренд: NTI Страницы: 7

Бренд: Vigitron Страницы: 2

Бренд: HiLook Страницы: 10

Бренд: Wisenet Страницы: 2

Бренд: ION Страницы: 48

Бренд: Vectaire Страницы: 6

Бренд: iWeld Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды