Honeywell ADEMCO LYNXR-EN Скачать руководство пользователя

Страница: 47 / 64

– 47 –

Summary Of Audible Notification

*UPPER CASE indicates announcements after pressing

STATUS

once. Lower case indicates announcements after

pressing

STATUS

twice.

SOUND CAUSE

DISPLAY

ANNOUNCEMENT*

INTERRUPTED
Speaker and
external piezo and
bell

FIRE ALARM

FIRE

ALARM

is displayed; zone

number in alarm displayed.

fire alarm + zone voice

descriptor

(Voice descriptor is
interlaced with the siren and
sounds every 45 seconds)

CONTINUOUS
Speaker and
external piezo and
bell

BURGLARY/AUDIBLE

EMERGENCY ALARM

ALARM

is displayed; zone number

in alarm displayed.

alarm + zone voice
descriptor
(Voice descriptor is
interlaced with the siren and
sounds every 45 seconds)

ONE SHORT BEEP
(not repeated)
Speaker and
external piezo

a. SYSTEM DISARM
b. SYSTEM ARMING

ATTEMPT WITH AN
OPEN ZONE.

c. BYPASS VERIFY

a. Green LED on steady
b. The number of the open protection

zone is displayed after pressing

STATUS

c. Numbers of the bypassed

protection zones are displayed
(One beep is heard for each zone
displayed).

a. DISARMED–READY TO

ARM

b. DISARMED–NOT READY

TO ARM

c. zones bypassed

ONE SHORT BEEP
(once every 45
secs) Speaker and
external piezo

a. SYSTEM IS IN TEST

MODE

b. LOW BATTERY AT A

TRANSMITTER

c. SYSTEM LOW

BATTERY

d. FAIL TO

COMMUNICATE

a. Opened zone identifications will

appear.

LOW BAT

displayed with zone

number of transmitter.

LOW BAT

displayed with no zone

no.

displayed with no zone no.

a. No announcement

b. low b zone voice

descriptor

c. system low battery

d. check system

TWO SHORT
BEEPS
Speaker and ext.
piezo

ARM AWAY OR MAXIMUM

AWAY or AWAY + INSTANT

displayed. Red ARMED indicator is
lit.

ARMED AWAY [INSTANT] –
EXIT NOW

THREE SHORT
BEEPS
Speaker and
external piezo

a. ARM STAY OR INSTANT

b. ZONE OPENED WHILE

SYSTEM IS IN CHIME
MODE.

STAY

STAY + INSTANT

displayed. Red ARMED indicator is
lit.

CHIME

displayed, number of open

protection zone will be displayed if
the Status key is pressed.

a. ARMED STAY [INSTANT]

– EXIT NOW

b. zone voice descriptor

RAPID BEEPING
Speaker and
external piezo

a. TROUBLE

b. MEMORY OF ALARM

FAULT

displayed. Number of

troubled protection zone is
displayed.

FIRE ALARM

ALARM

displayed; zone number in alarm is
displayed.

a. fault + zone voice

descriptor

b. fire alarm or alarm + zone

voice descriptor

SLOW BEEPING
Speaker and
external piezo

a. ENTRY DELAY

WARNING

b. EXIT DELAY WARNING

a. Exceeding the delay time without

disarming causes alarm.

AWAY

AWAY + INSTANT

displayed

a. DISARM SYSTEM NOW

b. ARMED [AWAY]

[INSTANT] – EXIT NOW

Содержание ADEMCO LYNXR-EN
































































Результаты поиска

Содержание ADEMCO LYNXR-EN

Отзывы:

Похожие инструкции для ADEMCO LYNXR-EN

Бренды по названию

Популярные бренды

Honeywell ADEMCO LYNXR-EN, Руководство пользователя

Результаты поиска

Содержание ADEMCO LYNXR-EN

Отзывы:

Похожие инструкции для ADEMCO LYNXR-EN

Бренды по названию

Популярные бренды