Honda VFR1200F Скачать руководство пользователя страница 27

Страница: 27 / 143

Operation Guide

D indicator

Comes on when the D mode is selected in the AT MODE.

P.38

S indicator

Comes on when the S mode is selected in the AT MODE.

P.38

Gear position indicator

The gear position is shown in the gear position indicator when the D, S mode or MT MODE
are selected.

“-” appears for a few seconds and then goes off when the engine starts.

“-” flashes when the engine stop switch position is changed from RUN to OFF with the
ignition switch ON.

“-” flashes when the ignition switch is turned ON with the engine stop switch OFF.

The indicator may flash if:

The front wheel leaves the ground.

You turn the wheel while the motorcycle is upright on the stand.

This is normal. To operate the system again, turn the ignition switch OFF, then ON again.

If the “-” indicator is blinking in the gear position window while riding:

P.93

31MGE601.indb 25

2010/03/08 18:05:25

Содержание VFR1200F
















































































































































Результаты поиска

Содержание VFR1200F

Отзывы:

Похожие инструкции для VFR1200F

Бренды по названию

Популярные бренды

Honda VFR1200F, Руководство пользователя

Результаты поиска

Содержание VFR1200F

Отзывы:

Похожие инструкции для VFR1200F

Бренды по названию

Популярные бренды