Honda Forza 300 2013 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 119

Honda Forza 300 2013 Скачать руководство пользователя страница 101

Instruments, Controls, & Other Features

98

In

fo
rma

tio

n

The display locks 999,999 when the read-out
exceeds 999,999.

The tripmeter A and B return to 0.0 when the
read-out exceeds 999.9.

The Honda Ignition Security System (HISS)
immobilizes the engine’s ignition system if an
improperly-coded key is used to try and start
the engine. When the ignition switch is turned
OFF, the HISS immobilizer system is always alert,
even if the HISS indicator is not flashing.
If the ignition switch is turned ON with the
engine stop switch in the run position, the HISS
indicator turns on and goes off after a few
seconds to indicate it is OK to start the engine.

2

HISS Indicator Does Not Turn off

P. 79

The HISS indicator starts flashing every 2
seconds for 24 hours after the ignition switch is
turned OFF. To prevent or to restore the HISS
indicator flashing:

1.

With the ignition switch ON, press the MODE
button (

2

P. 20) to select the odometer.

2

P. 21

2.

Press and hold the MODE button for 2
seconds or more.

u

The HISS indicator flashes once.

3.

Turn the ignition switch OFF.

EC Directive

This immobilizer system complies with R & TTE
(Radio and Telecommunications Terminal
Equipment and the mutual recognition of their
conformity) Directive.

Odometer

Tripmeter

HISS (Except U, KO type)

«
...
99
100
101
102
103
...
»

Содержание Forza 300 2013
























































































































Отзывы:

Нет отзывов