Honda FJ500 Скачать руководство пользователя

Страница: 63 / 70

9. TRANSPORTING/STORAGE

When transporting the tiller, turn the fuel valve OFF and keep the tiller

level to prevent fuel spillage. Fuel vapor or spilled fuel may ignite.

Before storing the unit for an extended period:

1.Be sure the storage area is free of excessive humidity and dust.

2.Drain the fuel:

Gasoline is flammable and explosive under certain conditions. Do not

smoke or allow flames or sparks near the equipment while draining

fuel.

a. Place an approved gasoline container below the carburetor, and

use a funnel to avoid spilling fuel.

To drain the gasoline of the caburetor only, place a suitable container

under the caburetor and follow procedures “e.” and “f.”.

b. Remove the sediment cup and O-ring.

c. Turn the fuel valve to the ON position. Drain the gasoline into a

suitable container.

FUEL VALVE

O-RING

(Replace)

SEDIMENT CUP

36V426020.book Page 61 Tuesday, June 25, 2013 10:43 AM

Содержание FJ500







































































Результаты поиска

Содержание FJ500

Отзывы:

Похожие инструкции для FJ500

Бренды по названию

Популярные бренды

Honda FJ500, Руководство пользователя

Результаты поиска

Содержание FJ500

Отзывы:

Похожие инструкции для FJ500

Бренды по названию

Популярные бренды