Honda FJ500 Скачать руководство пользователя

Страница: 48 / 70

4.Spark plug service

Recommended spark plug:

BPR5ES (NGK)

W16EPR-U (DENSO)

To ensure proper engine operation, the spark plug must be properly

gapped and free of deposits.

1.Remove the spark plug cap.

Use the spark plug wrench to remove the spark plug.

If the engine has been running, the muffler will be very hot. Be careful

not to touch the muffler.

2.Visually inspect the spark plug. Discard it if the insulator is cracked

or chipped. Clean the spark plug with a wire brush if it is to be

reused.

3.Measure the plug gap with a feeler

gauge.

Correct as necessary by bending

the side electrode.

The gap should be:

0.7–0.8 mm (0.028–0.031 in)

SPARK PLUG CAP

SPARK PLUG WRENCH

0.7

–

0.8 mm

(0.028

–

0.031 in)

36V426020.book Page 46 Tuesday, June 25, 2013 10:43 AM

Содержание FJ500







































































Результаты поиска

Содержание FJ500

Отзывы:

Похожие инструкции для FJ500

Бренды по названию

Популярные бренды

Honda FJ500, Руководство пользователя

Результаты поиска

Содержание FJ500

Отзывы:

Похожие инструкции для FJ500

Бренды по названию

Популярные бренды