Honda EU3200i Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 100

background image

CONSUMER INFORMATION

84

Emission Control System Warranty

Your new Honda Power Equipment engine complies with the U.S. EPA,
Environment Canada, and State of California (models certified for sale in
California only) emission regulations. American Honda Motor Co., Inc. provides
the emission warranty coverage for engines in the United States and its
territories. Honda Canada Inc. provides the emission warranty for engines in the
13 provinces and territories of Canada. In the remainder of this Emission Control
System Warranty, American Honda Motor Co., Inc. and Honda Canada Inc. will
be referred to as Honda.

CALIFORNIA EXHAUST AND EVAPORATIVE EMISSIONS CONTROL
WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Honda are pleased to explain the
exhaust and evaporative emissions (“emissions”) control system warranty on
your 2021 and later Honda Power Equipment engine. In California, new
equipment that use small off-road engines must be designed, built, and
equipped to meet the State's stringent anti-smog standards. Honda must
warrant the emissions control system on your power equipment engine for the
periods of time listed below provided there has been no abuse, neglect, or
improper maintenance of your small off-road engine or equipment leading to
the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or
fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel
lines (for liquid fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps
and other associated components. Also included may be hoses, belts,
connectors, and other emission-related assemblies (see page 88 for additional
covered parts).

Where a warrantable condition exists, Honda will repair your power equipment
engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The exhaust and evaporative emissions control system on your Honda power
equipment engine is warranted for two years. If any emissions-related part on
your Honda power equipment engine is defective, the part will be repaired or
replaced by Honda.

«
...
84
85
86
87
88
...
»

Содержание EU3200i





































































































Отзывы:

Нет отзывов

Похожие инструкции для EU3200i

Бренд: Teac Страницы: 6

Бренд: Fenton Страницы: 16

Yakumo DVD Travelle

Бренд: YAKUMO Страницы: 40

Бренд: Consort Страницы: 30

Бренд: Coby Страницы: 1

Бренд: Chevron Страницы: 26

Бренд: Covidien Страницы: 112

Бренд: Clever Страницы: 26

Бренд: Caliber Страницы: 18

Бренд: LENCO Страницы: 68

Бренд: Sangean Страницы: 151

Бренд: Harman Kardon Страницы: 6

Бренд: Elektro-Automatik Страницы: 44

Бренд: DUROMAX Страницы: 64

Бренд: DUROMAX Страницы: 64

Бренд: DUROMAX Страницы: 66

Бренд: DUROMAX Страницы: 70

Бренд: DUROMAX Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды