Honda EU3200i Скачать руководство пользователя страница 15

Страница: 15 / 100

INITIAL USE INSTRUCTIONS

ENGINE OIL

The generator is shipped

WITHOUT OIL

in the engine.

1. Place the generator on a level surface.

2. Loosen the maintenance cover screw and remove the maintenance cover.

3. With the generator in a level position, remove the oil filler cap by turning it

counterclockwise.

4. Add enough oil to bring the oil level to the upper limit of the oil filler neck.

SAE10W-30 API service category SJ or later (or equivalent) is recommended
for general use; for additional recommendations (see page 14).

Maximum oil capacity:

15 oz (0.46 L)

Do not overfill the engine with oil.

If the engine is overfilled, the excess oil

may be transferred to the air cleaner housing and air filter.

5. Screw in the oil filler cap securely.

6. Reinstall the maintenance cover and tighten the maintenance cover screw

securely.

MAINTENANCE COVER

MAINTENANCE COVER SCREW

OIL FILLER CAP

UPPER LIMIT
(The oil exists to
the oil filler neck.)

OIL FILLER NECK

DIPSTICK

Содержание EU3200i





































































































Результаты поиска

Содержание EU3200i

Отзывы:

Похожие инструкции для EU3200i

Бренды по названию

Популярные бренды

Honda EU3200i, Руководство пользователя

Результаты поиска

Содержание EU3200i

Отзывы:

Похожие инструкции для EU3200i

Бренды по названию

Популярные бренды