Honda EU3200i Скачать руководство пользователя страница 60

Страница: 60 / 100

SERVICING YOUR GENERATOR

4. Inspect the spark plug. Replace it if

the electrodes are worn or fouled, or
if the insulator is cracked or chipped.
Clean the spark plug with a wire
brush if it is to be reused.

5. Measure the spark plug electrode

gap with a wire-type feeler gauge.
Correct the gap, if necessary, by
carefully bending the side electrode.

Spark plug gap:

0.024–0.028 in (0.6–0.7 mm)

6. Make sure that the spark plug sealing washer is in good condition, and thread

the spark plug in by hand to prevent cross-threading.

7. After the spark plug is seated, tighten with a spark plug wrench to compress

the washer.
If reinstalling a used spark plug, tighten 1/8–1/4 turn after the spark plug is
seated.
If installing a new spark plug, tighten 1/2 turn after the spark plug is seated.

Torque:

9 lbf∙ft (12 N∙m, 1.2 kgf∙m)

A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the cylinder head.

8. Reinstall the spark plug cap on the spark plug securely.

9. Reinstall the spark plug maintenance cover.

SIDE ELECTRODE

SEALING WASHER

0.024–0.028 in
(0.6–0.7 mm)

INSULATOR

Содержание EU3200i





































































































Результаты поиска

Содержание EU3200i

Отзывы:

Похожие инструкции для EU3200i

Бренды по названию

Популярные бренды

Honda EU3200i, Руководство пользователя

Результаты поиска

Содержание EU3200i

Отзывы:

Похожие инструкции для EU3200i

Бренды по названию

Популярные бренды