Honda CRF125F 2021 Скачать руководство пользователя страница 89

Страница: 89 / 132

4. Turn the adjusting nut (3) on both the

right and left chain adjusters an equal
number of turns to increase or decrease
chain slack.
Align the Notches (4) on the chain
adjusters with the graduated scales (5)
on both sides of the swingarm.

If the drive chain slack is excessive when
the rear axle is moved to the furthest limit
of adjustment, the drive chain is worn and
must be replaced.

5. Tighten the rear axle nut to:

62 N·m (6.3 kgf·m, 46 lbf·ft)

6. Tighten the adjusting nuts lightly, then

tighten the lock nuts by holding the
adjusting nuts with a spanner.

7. Recheck drive chain slack.
8. Rear brake pedal freeplay is affected

when repositioning the rear wheel to
adjust drive chain slack. Check rear
brake pedal freeplay and adjust as
necessary (page 26).

If a torque wrench is not used for this
installation, see your dealer as soon as
possible to verify proper assembly.

Lubrication:
Lubricate every 500 km (300 miles) or
sooner if chain appears dry.

Recommended lubricant:

Drive chain lubricant
If not available, use SAE 80 or 90 gear oil.

Saturate each chain link joint so that the
lubricant penetrates between the link plates,
pins, bushings, and rollers.

37K28B31.book Page 79 Monday, July 26, 2021 6:11 PM

Содержание CRF125F 2021





































































































































Результаты поиска

Содержание CRF125F 2021

Отзывы:

Бренды по названию

Популярные бренды

Honda CRF125F 2021, Руководство пользователя

Результаты поиска

Содержание CRF125F 2021

Отзывы:

Бренды по названию

Популярные бренды