manualshive.com logo in svg

Honda CRF125F 2021, Руководство пользователя

Поделиться
Скачать
Honda CRF125F 2021 Скачать руководство пользователя страница 38

28

CLUTCH

Clutch adjustment may be required if the 
motorcycle stalls when shifting into gear or 
tends to creep; or if the clutch slips, causing 
acceleration to lag behind engine speed. 
Minor adjustments can be made with the 
clutch cable adjuster (4) at the clutch lever 
(1).
Normal clutch lever freeplay is:

10 – 20 mm (0.4 – 0.8 in)

1. Pull back the rubber dust cover (2). 
2. Loosen the lock nut (3) and turn the 

clutch cable adjuster (4). Tighten the 
lock nut and check the adjustment.

3. If the adjuster is threaded out near its 

limit or if the correct freeplay cannot be 
obtained, loosen the lock nut and turn in 
the clutch cable adjuster completely. 
Tighten the lock nut and install the 
rubber dust cover.

(1) Clutch lever

(1)

(2) Rubber dust cover
(3) Lock nut
(4) Clutch cable adjuster

(A)Increase freeplay
(B)Decrease freeplay

(4)

(A)

(3)

(B)

(2)

37K28B31.book  Page 28  Monday, July 26, 2021  6:11 PM

Содержание CRF125F 2021





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды