Honda CRF125F 2021 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 132

Honda CRF125F 2021 Скачать руководство пользователя страница 34

24

MAJOR COMPONENTS

(Information you need to operate this motorcycle)

BRAKES
Front Brake

This motorcycle has a hydraulic front disc
brake.
As the brake pads wear, brake fluid level
drops.
There are no adjustments to perform, but
fluid level and pad wear must be inspected
periodically. The system must be inspected
frequently to ensure there are no fluid leaks.
If the brake lever free travel becomes
excessive and the brake pads are not worn
beyond the recommended limit (page 86),
there is probably air in the brake system and
it must be bled. See your dealer for this
service.

Brake Fluid Level:
With the motorcycle in an upright position,
check the fluid level. It should be above the
LWR mark (1). If the level is at or below the
LWR mark, check the brake pads for wear
(page 86).

Worn pads should be replaced. If the pads
are not worn, have your brake system
inspected for leaks.

The recommended brake fluid is Honda
DOT 3 or DOT 4 brake fluid from a sealed
container, or an equivalent.

(1) LWR mark

(1)

37K28B31.book Page 24 Monday, July 26, 2021 6:11 PM

«
...
32
33
34
35
36
...
»

Содержание CRF125F 2021





































































































































Отзывы:

Нет отзывов