manualshive.com logo in svg

Honda CRF125F 2021, Руководство пользователя

Поделиться
Скачать
Honda CRF125F 2021 Скачать руководство пользователя страница 86

76

DRIVE CHAIN

Refer to the Safety Precautions on page 55.

The service life of the drive chain (1) is 
dependent upon proper lubrication and 
adjustment. Poor maintenance can cause 
premature wear or damage to the drive 
chain and sprockets.
The drive chain should be checked and 
lubricated as part of the Pre-ride Inspection 
(page 43). Under severe usage, or when the 
motorcycle is ridden in unusually dusty or 
muddy areas, more frequent maintenance 
will be necessary.

Inspection:
1. Turn the engine off, place the 

motorcycle on its side stand and shift the 
transmission into neutral.

2. Check slack in the lower drive chain run 

midway between the sprockets.
Drive chain slack should be adjusted to 
allow the following vertical movement 
by hand:

25 – 35 mm (1.0 – 1.4 in)

3. Roll the motorcycle forward. Stop. 

Check the drive chain slack. Repeat this 
procedure several times. Drive chain 
slack should remain constant. If the 
chain is slack only in certain sections, 
some links are kinked and binding. 
Binding and kinking can frequently be 
eliminated by lubrication.

Excessive chain slack may allow the drive 
chain to damage the engine cases.

(1) Drive chain

(1)

37K28B31.book  Page 76  Monday, July 26, 2021  6:11 PM

Содержание CRF125F 2021





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды