background image

Page 13 — English

OPERATION

High Pressure Cleaning:
Squeeze the high pressure trigger located beneath the rear 
handle. This will provide a spray of water at high pressure. 
Low Pressure (High Flow) Cleaning:
Move the low pressure (high flow) lever on top of the trigger han-
dle forward. This will provide a spray of water at low pressure.
NOTE: When using low pressure (high flow) cleaning only, 
depress the high pressure trigger lock-out to prevent ac-
cidental depressing of the high pressure trigger. 
Combination Cleaning/Rinsing: 
To apply a high pressure stream and rinse the area with water 
at the same time (for instance, in a heavily soiled area), move 
the low pressure (high flow) lever forward and depress the 
high pressure trigger.
NOTE: Any cleaning or rinsing method using high pressure 
spray requires that the ON/OFF switch be in the ON position. 
For methods using low pressure only, the switch may be in 
either the ON or OFF position. 

USING THE NOZZLES

See Figure 15.

Before starting any cleaning job, determine the best nozzle 
for the job. The 15˚ nozzle is for general purpose or large 
surfaces and the turbo nozzle gives up to 50% more clean-
ing power.

Nozzle

Application

15º

For narrow surfaces
• Removing heavy mildew stains
• Removing marine growth from boats and 

marine equipment

•  Removing  rust  from  steel  and  oxidation 

from aluminum

• Removing grease or dirt from equipment
•  Removing  paint  from  wood,  masonry  or 

metal

Turbo

Pencil jet nozzle rotates at high speed to 

increase intensity and cleaning area of the 
spray. Spray pattern will cover an area from 4 
to 8 in. wide depending on distance between 
wand and surface being cleaned.
• Rust removal
• Non-painted metal or plastic tank cleaning
• Washing concrete
• Removing gum from sidewalks
• Boat cleaning
• Cleaning dirty garage floors
• Removing mud and clay from hard surfaces 

like concrete, brick, or stone

WARNING:

NEVER change nozzles without locking the lock-out on 
the trigger handle and never point the wand at your face 
or at others. The quick-connect feature contains small 
springs that could eject the nozzle with some force. Fail-
ure to heed this can cause personal injury.

  Turn off the pressure washer and shut off the water sup-

ply. Pull trigger to release water pressure.

  Engage the lock-out on the trigger handle by pushing up 

on the lock-out until it clicks into the slot.

  Pull back the quick-connect collar.

  Push the nozzle into place in the spray wand. 

  Push the collar forward so that the nozzle is secured 

properly. Check to see that the nozzle is secure.

To disconnect a nozzle from the trigger handle once the 
cleaning job is complete:

  Turn off the pressure washer and shut off the water sup-

ply. Pull trigger to release water pressure.

  Engage the lock-out on the trigger handle by pushing up 

on the lock-out until it clicks into the slot.

  Remove the nozzle by placing hand over nozzle then 

pulling back the quick-connect collar. Place nozzle in the 
nozzle storage area on the top of the machine.

USING THE HIGH PRESSURE HOSE

The high pressure hose features an outer covering that pro-
vides strength to the hose. If the outer covering becomes 
damaged, the hose must be replaced immediately. 

Do not 

use a high pressure hose if the outer covering is damaged.
To prevent damage to the outer covering:

  Inspect the hose before every use. 

  Fully unwrap and straighten hose before use.

  Do not allow the high pressure hose to be kinked.

  Keep hose away from hot surfaces and sharp edges.

  Do not pull unit by high pressure hose.

  Do not allow hose to be crushed or wrapped around 

objects.

Содержание UT80720





















































Отзывы: