Home Plus SoftPlus SP-5810XTR2 Series Скачать руководство пользователя страница 34

Страница: 34 / 40

treatment

rapid rinse

backwash

draw

tank refill

pause

Aux. 2 Cycle Based

treatment

rapid rinse

backwash

draw

tank refill

pause

METER

Parameter

Setting

meter type

1.25” turbine

generic

plumbing leak detect

OPERATION DURING A POWER FAILURE

The 5810XTR2 valve/controller includes integral power backup. In the event of power failure,

the control shifts into a power-saving mode. The display and motor shut down, but it

continues to keep track of the time and day for a minimum of 48 hours.

The system configuration settings are stored in a non-volatile memory and are stored

indefinitely with or without line power. The Time of Day flashes when there has been a

power failure. Press any button to stop the Time of Day from flashing.

If power fails while the unit is in regeneration, the control will save the current valve position

before it shuts down. When power is restored, the control will resume the regeneration cycle

from the point where power failed. Note that if power fails during a regeneration cycle, the

valve will remain in its current position until power is restored.

Содержание SoftPlus SP-5810XTR2 Series









































Результаты поиска

Содержание SoftPlus SP-5810XTR2 Series

Отзывы:

Похожие инструкции для SoftPlus SP-5810XTR2 Series

Бренды по названию

Популярные бренды

Home Plus SoftPlus SP-5810XTR2 Series, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание SoftPlus SP-5810XTR2 Series

Отзывы:

Похожие инструкции для SoftPlus SP-5810XTR2 Series

Бренды по названию

Популярные бренды