HOKLARTHERM Riga 2 S/2 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

background image

13

Pos. 4.0

Pos. 4.1

Pos. 4.3

Pos. 4.3
Insert 2 Hexagon Bolts
M 6x16

Rear Wall Window Assembly:

The Rear Wall Window is assembled
the same way as the Roof Window or
Skylight. See Previous page and
drawings on this page.
One exception: the Y-seal goes into all 4
profiles.

Attention!

Insert 2 Hexagon Bolts (M 6 x16) into the
bottom profile of the Rear Wall Window -
in order to be able to attach the Rear
Wall Window Opener (adjustable arm)
later.

4.0

PVC-corner connector

2.4“ x 2.4“ x 1.1“ 4

4.1

Aluminum-corner connector

1.2“ x 1.2“ x 0.4“ 4

4.2

Vertical Window Support (without holes)

50.7“

4.3

Horizontal Window Frame Supports

30.1“

2

4.4

Vertical Window Support with holes (for hinges)

50.7“

1

Y-seal

15 feet

Part of the Total Parts List

Pos. 4.2

Pos. 4.4

Mounting of the skylight (roof window):

Slide the narrow circular channel sticking out of the top Skylight Profile (#5.0) of the fully
assembled roof window (see Ill. 3, page 8) into the wider circular channel on top of the Roof
Beam. With the rubber mallet move the window in position so that when it closes it fits between
two Curved Center Profiles (#2.2).

Glazing channel

Bolt channel

Y-seal

Pos.

designation

length

number

Parts list for Rear Wall Window

«
...
11
12
13
14
15
...
»

Содержание Riga 2 S/2





















Отзывы:

Нет отзывов

Похожие инструкции для Riga 2 S/2

essential Series

Бренд: Gabriel Ash Страницы: 40

Бренд: Alice's Garden Страницы: 16

Бренд: BCP Страницы: 8

Бренд: Dancover Страницы: 20

Бренд: Dancover Страницы: 26

Бренд: ACD Страницы: 58

Бренд: Halls Greenhouses Страницы: 36

Бренд: LAMS Страницы: 32

Бренд: LAMS Страницы: 80

Бренд: Argos Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды