background image

12

 Pos.

      designation

length

         number

Pos. 4.0

Pos. 4.1

Pos. 4.0

Pos. 4.1

Pos. 5.0

Pos. 5.0

Pos. 5.1

Pos.5.1

Ill. 3:

2  H exagon B olts
M6 x 16

Parts list for skylight

    4.0

PVC-angle bracket

                      2.7“ x 1.1“ x 0.4“

4

    4.1

Alu-angle connection with recessed screw

            1.2“ x 1.2“ x 0.4“

4

    5.0

Skylight (roof window) cross-rail

         41“

2

    5.1

Skylight Side Bar

         24.8“

2

Y-seal

                          11.5 ft.

-top-

milling to have it push into the ridge

B olt channel

G laz ing
channel

Y-seal

Skylight or Roof Window Assembly

:

The aluminum profiles of the Skylight are all bound together in one
bundle .
Lay out the profiles as shown in the above picture and insert the big
PVC- corner connectors (#4.0) and the aluminium corner connectors
(#4.1) into the appropriate profile channels (it is a snug fit). Make sure
to insert 2 Hexagon Bolts (M 6x16) into one of the Skylight profiles
(#5.0) (This one will become the bottom of the window) as these will
be later used to attach the Automatic Window Opener.

Attention!

 

In order for the window to be able to close correctly you

must make sure that the 2 ends with a slight cut-out of each of the
vertical/side profiles are facing to the top. (Look carefully at each end
and put the ends with the shorter round channels on the top). See
picture on top left.

Attention!

 

The appropriate size Glazing Panel has to be inserted into

the profiles while assembling the frame.Use the Allen key to tighten all
the aluminum corner connectors.
Next insert (or pull-in) the rubber Y-seal into the narrow circular
channel located on the outer edge of the two side profiles and the
bottom profile. See picture on left bottom.
Then if you wish (optional, but recommended) seal the outside of the
Skylight with silicon (use enclosed tube).

Содержание Riga 2 S/2





















Отзывы: