Hokkaido HCND 261 X Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 40

background image

- 11 -

INDOOR AND OUTDOOR’S UNITS OUTLINE

The Figure below is for explanation purpose only. The real appearance of the components could be

rather different.

Indoor Unit

Outdoor Unit

Unit operation section

Air return grid

Takes in the indoor air

Left/right air flow

direction adjusting fin

Operational performance/indications

Up/down air flow

direction adjusting flap

Air outlet

Air filter

Drain tube

Air inlet

at sides & rear surface

Refrigerant piping

connection, Electric

wiring cord

Emergency Operation Key

Note: Do not open the frontal panel at an angle over 60 degrees. Do not operate the Units with too much force.

How to close

How to open

Air discharge vent

Lightly push both sides of the frontal panel at the bottom
and pull it to this side till a resistance is felt.

This button can be used as an emergency measure to turn
on/off Unit when remote controller is not available.

Air blows out from here.

Removes dust or dirt out of the inlet air.

Drain the water dehumidified out of the air.

Push down the frontal panel and then push sides of air inlet
grid at the bottom.

«
...
9
10
11
12
13
...
»

Содержание HCND 261 X









































Отзывы:

Нет отзывов

Похожие инструкции для HCND 261 X

Бренд: Zibro Страницы: 102

Бренд: Olimpia splendid Страницы: 24

Бренд: Halogen Страницы: 4

Бренд: 3M Страницы: 4

Бренд: Trion Страницы: 4

Бренд: Daikin Страницы: 12

Бренд: Midea Страницы: 64

Бренд: Zelmer Страницы: 68

Бренд: EAS Electric Страницы: 234

DOM413 BL-198DLR

Бренд: Livoo Страницы: 10

Бренд: Jocel Страницы: 72

Бренд: Walter Roller Страницы: 36

Бренд: Turbo Air Страницы: 33

Бренд: General Страницы: 20

Бренд: King Industrial Страницы: 6

Бренд: Danby Страницы: 76

Бренд: Radialight Страницы: 16

Бренд: gmc aircon Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды