background image

- 8 -

SAFETY PRECAUTIONS

Installation

Never try to install this Unit by yourself, i.e. without the support of Tachnical Personnel. Never try to reapir 

the Unit by yourself. The Unit's components can be reached only by opening or removing the covering 

panels, and this involves exposure to high voltage. Even by disconnecting power supply, it is not always 

possible to avoid the risk of electric shocks.

• Please always contact the Dealer or the Authorized Service Center for installation.
Never attempt to install the air conditioner by yourself, because improper installation 
could cause electric shock, injuries, water leakage or fire.

• Please always contact the Dealer or the Authorized Service Center for any servicing 
operation or special maintenance.
Never try to repair or carry out special maintenance by yourself. Improper repair or 
maintenance could cause electric shock, injuries, water leakage or fire.

Please confirm that installation has been carried out according to the following prescriptions:

WARNING

!

!

!

•  When  instaling,  all  possible  countermeasures  must  be  taken  to  avoid  refrigerant 

leaks. If there is a high concentration of refrigerant gas in the room, oxygen lack may 

occur.

• Do not install the air conditioner near burners, heat sources or flammable gas. This 

is to avoid the risk of malfunctioning, fire or explosion.

• Ensure that a circuit breaker has been installed on the power supply line of the air 

conditioner, to avoid the risk of electric shocks.

•  When  installing  in  a  small  room,  countermeasures  should  be  taken  in  case  of  a 

refrigerant leak exceeds the proper range. Otherwise, it will cause asphyxia.

CAUTION

!

!

!

!

• Ensure that drain hose and drain pipe installation has been carried out correctly. 

Incorrect installation or maintenance will cause water leakage.

CAUTION

!

!

!

• Ensure that Indoor and Outdoor Units have been properly grounded. 

Defective grounding could cause electric shock.

!

• This kind of appliance needs a specific circuit breaker with proper 

protective devices against overcurrents and short circuits (fuses or 

automatic switches).

Circuit

breaker

(specific)

Содержание HCND 261 X









































Отзывы: