HobbyKing Turnigy V-Bar 600 Скачать руководство пользователя страница 19

Страница: 19 / 19

1
9

(Default 100)

inclining rightward

7. ELELSTOP

7. ELELSTOP-----

-----

----- Elevator Back

Elevator Back

ward Stop Gain

Item

Content

60 ~ +160

(Default 100)

The stopping gain when inclining backward. The stop speed against side wind and

inclining backward

8. ELERSTOP

8. ELERSTOP----

----

---- Elevator Front

Elevator Front

ward Stop Gain

Item

Content

60 ~ +160

(Default 100)

The stopping gain when inclining frontward. The stop speed against side wind and

inclining frontward

9. V-SWPLRO-----Settings of Virtual Swashplate Rotation

Item

Content

-89 ~ +89

(Default 0)

The phase compensation of swashplate, and the precision is 1

. Regarding 2-blade

rotor head, this value is 0. Mainly used fro the phase compensation of multi- blade
(above 3 blades) rotor head.

Double check your work after setting!

Warm tips: Please take care of Turnigy® V-Bar 600

！

Do not

open the bottom cover of Turnigy® V-Bar 600

housing to avoid damaging product.

Содержание Turnigy V-Bar 600




















Результаты поиска

Содержание Turnigy V-Bar 600

Отзывы:

HobbyKing Turnigy V-Bar 600, Руководство пользователя, Страница: 19 / 19

Результаты поиска

Содержание Turnigy V-Bar 600

Отзывы: