HobbyKing Turnigy V-Bar 600 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

HobbyKing Turnigy V-Bar 600 Скачать руководство пользователя страница 11

11

in deadband zone.Increase RUD-DEAD.

SWPL-TYP SRV-DIR Submenu Configuration Steps:

1. GYRO-POS -----Turnigy® V-Bar 600 Placement Selection

Item

Content

NORM

(Default)

Turnigy® V-Bar 600 runs parallel to the helicopter (nose) and can be placed at the
top and the bottom. It shall be powered on when changing the placement.

ROT-90

Turnigy® V-Bar 600 runs perpendicular to the helicopter (nose) and can be placed
at the top and the bottom. It shall be powered on when changing the placement.

2

、

、

、

、

SWPL-TYPE -----Swashplate Type Selection

Item

Content

120DEG

(Default)

Transmitter should be in H1 model. Turnigy® V-Bar 600 controls 3 swashplate
servos after being mixed controlled by Turnigy® V-Bar 600 using 3-point (120°)
link method.

135DEG

Transmitter should be in H1 model. Turnigy® V-Bar 600 controls 3 swashplate
servos after being mixed controlled by Turnigy® V-Bar 600 using 3-point
(135°/140°) link method.

«
...
9
10
11
12
13
...
»

Содержание Turnigy V-Bar 600




















Отзывы:

Нет отзывов