manualshive.com logo in svg

Hobbico TWINSTAR, Руководство по сборке

Поделиться
Скачать
Hobbico TWINSTAR Скачать руководство пользователя страница 2

Take a moment now to
match the box contents
with the items listed
below. Following the
Twinstar assembly
instructions will be
quite easy if you identify
and organize the parts
before you begin.

Replacement Parts Available

HCAA3690 ...Wing Kit

HCAA3694....Landing Gear Set

HCAA3691 ...Fuselage Kit

HCAA3695....Nacelle Set (L&R)

HCAA3692 ...Fin Set

HCAA3696....Nacelle Cover

HCAA3693 ...Spinner

HCAA3697....Nose Cone (2 pcs.)

2

Landing Gear

Part #

Quantity

15 Main Landing Gear....................2
5

Nose Gear .................................1

4

Steering Arm .............................1

14 Wheels ......................................3
66 Wheel Collars ............................5
67 3 x 8mm Screw .........................1
68 3 x 5mm Screw .........................5

Wing Assembly

Part #

Quantity

6

Dihedral Brace .........................................3

7

Right Wing Panel .....................................1

8

Left Wing Panel........................................1

28

*

Clevises ..................................................2

40 4mm Washers..........................................2
41 4 x 35mm Bolt ..........................................2
42 4mm O-ring ..............................................2
43 Engine Nacelle (R)...................................1
44 Engine Nacelle (L) ...................................1
45 Wing Bolt Plate ........................................1
46 Servo Tray (Wing)....................................3
47

*

Aileron Control Horns .............................2

50 Fuel Tank Brace.......................................2
61 Front Root Ribs........................................2
62 Rear Root Ribs ........................................2

40

42

47

28

46

45

39

Y

ou’re about to build in just hours what took aviation

pioneers years—a powered machine that flies. Specially
created for you and other experienced radio control
modelers, Hobbico’s Twinstar offers nearly all the
excitement of piloting a real airplane...and develops skills
that will take you anywhere you want in your hobby.

41

*Parts marked with an asterisk are found on the plastic parts tree.

Know Your Model’s Parts

Tail Assembly

Part #

Quantity

1

Stabilizer and Elevator ..................1

16 Rudder and Fin..............................1
28

*

Clevises .......................................5

29

*

Control Horns...............................2

31 2mm x 18 mm Machine Screws ....4
53 Dorsal Fin ......................................1
53 Dorsal Fin Decal............................1

30

28

31

29

Содержание TWINSTAR





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды