manualshive.com logo in svg

Hobbico TWINSTAR, Руководство по сборке

Поделиться
Скачать
Hobbico TWINSTAR Скачать руководство пользователя страница 13

Install the Blind Nuts:

❏

6. Slide a 4mm washer onto one of the 4mm wing

bolts. Slide the bolt through the wing hold-down plate.
Thread a 4mm blind nut with the “pronged” side up
partially onto the wing bolt from the underside of the
plate. Put a small amount of 6-minute epoxy onto the
prongs, then draw it up into the plate by tightening the
bolt. Repeat this process for the other blind nut. Be
careful not to get any epoxy onto the threads of either
the nut or bolt during this procedure. Remove the bolts.

Install the Wing Bolts:

❏

7. Slide the bolt/washer combination from the last

step through the wing from the bottom. Slide a 4mm
rubber O-Ring onto the bolt from the top of the wing.
The O-Ring will keep the bolt from falling out of the wing
during transport.

Locate the Stabilizer Slot:

❏

1. Locate the horizontal stabilizer slot under the

covering on the tail section of the fuselage by pressing
lightly with your finger. The slot will be located on both
sides of the fuselage. Using a sharp hobby knife,
carefully remove the covering, exposing the slots. Note:
Do not cut into the wood around the slot.

Install the Stabilizer Mount:

❏

2. Locate the 1/8" (3mm) stabilizer mounting plate

and trial fit it into the bottom of the horizontal stabilizer
slot. Lightly sand the plate if necessary to obtain a good fit.

Glue the Mount into Position:

❏

3. Mix 1/8oz (3.5ml) of 30-minute epoxy. Using a

mixing stick, apply a generous amount of glue into the
slot and position the mounting plate, pressing it firmly

Install the Elevator and Rudder

13

Содержание TWINSTAR





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды