Hobart 6921 Series Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 262

Hobart 6921 Series Скачать руководство пользователя страница 108

Engine and Controls (cont.)

Trouble, Symptom & Condition

Test or Inspection

Corrective Action

c. Loose or binding governor

linkage.

d.

Check linkage ball joints and all
connections for looseness or
binding. Be sure linkage will
move from idle speed to full
speed without lost motion or
binding.

e. GAIN and STABILITY

controls improperly
adjusted.

Adjust GAIN and STABILITY
controls on control unit in accor-
dance with 2-3; Para. 4, E, (3).

f. Magnetic pickup signal

weak.

Check and adjust pickup. See
2-3, Para. 3, E, (2).

9.

Engine has slow response time.

a. Governor control unit

improperly adjusted.

Adjust. See 2-3; Para. 3, E, (3).

b. Actuator linkage binding.

Inspect and repair as required.

c. Engine needs tune-up.

Tune up as required. Refer to
Detroit Diesel Operator’s
Manual.

10. Engine “misses”. Runs

unevenly.

a. Insufficient fuel.

Check fuel flow in accordance
with Para. 9, F. Repair or
replace parts as required. Also
see ENGINE, Trouble 3.

b. Faulty injector.

Check injectors in accordance
with Para. 9, B.

c. Low compression pressure.

Check compression in accor-
dance with Para. 9, C. See
causes of low compression
listed under ENGINE, Trouble
3, B, above.

11. Engine lacks power.

a. Improper engine

adjustment and gear train
timing.

“Tune-up” the engine in
accordance with Detroit Diesel
Operator’s Manual.

b. Insufficient fuel.

See ENGINE, Trouble 3.

c. Insufficient inlet air.

Check as follows:

d. Damaged air cleaner.

Check air cleaner for “plugging”
and/or other damage.

e. Defective blower to-cylinder

block gasket

Replace the gasket if
necessary. If the blower is
removed, install a new gasket.

f. Plugged cylinder liner ports.

Clean ports if they are over
50% obstructed.

g. Faulty air blower.

Repair or replace.

h. Worn Engine.

See engine overhaul
instructions in engine manual.

OM-2040 / Operation and Maintenance Manual

90D20 / Generator Sets

Chapter 3-1

February 28/94 Revised

Page 16

«
...
106
107
108
109
110
...
»

Содержание 6921 Series







































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды