HME COMMUNICATOR COM6000BP Скачать руководство пользователя страница 11

Страница: 11 / 27

Battery Removal and Replacement

To change batteries:

If a battery

is weak when the COMMUNICATOR

power is turned on, a voice in the

earpiece will say “Battery low.”

If a battery becomes weak during

operation, a voice in the earpiece will

say “Change battery.” When this

happens, take the Communicator out

of its pouch and slide the battery-

release latch in the direction of the

arrow. Pull up on the end of the

battery near the latch and lift it out

of the Communicator, or turn the

Communicator over and catch the battery in your hand.

To replace batteries:

When replacing a battery in the

Communicator, place the end of the battery with the metal

contacts into the battery holder on the Communicator, in the same

position as the battery you removed. Press the top of the battery

carefully into the battery holder until it snaps into the latch.

Battery Charger

Up to four batteries can be charged in the charger at the same time.

Charging time is approximately 2.5 hours. The battery status lights

next to each charging port are explained below. Up to six fully

charged batteries can be stored in the battery storage ports.

A yellow light stays on steady next to each charging port while the

port is empty.

Insert a battery in one of the four charging ports until it clicks

in place.

If a yellow light is on steady next to a battery in a charging port, it

means CHARGE FAILED. Follow the diagnostic instructions on the

side of the battery charger.

If a yellow light is flashing next to a battery in a charging port, it

indicates CHARGE PENDING, which means the battery is too hot.

Lower the room temperature or move the charger to a cooler area.

A red CHARGING light will stay on next to a battery in a charging

port while the battery is charging.

A green READY light will go on next to a battery in a charging

port when the battery is fully charged.

Store fully charged batteries in the storage ports.

Figure 6. Communicator
battery-release latch

Figure 7. Batteries in charger

CAUTION:

Do not remove

batteries from

the charger until

the green READY

light is lit, or the

charger will reset

and the charge

cycle will begin

again.

Battery in

storage port

Battery in

charging port

Battery-release

latch

Содержание COMMUNICATOR COM6000BP




























Результаты поиска

Содержание COMMUNICATOR COM6000BP

Отзывы:

Похожие инструкции для COMMUNICATOR COM6000BP

Бренды по названию

Популярные бренды

HME COMMUNICATOR COM6000BP, Руководство по эксплуатации

Результаты поиска

Содержание COMMUNICATOR COM6000BP

Отзывы:

Похожие инструкции для COMMUNICATOR COM6000BP

Бренды по названию

Популярные бренды