HME Clear-Com 104G070 Скачать руководство пользователя страница 13

Страница: 13 / 18

TRANSCEIVER 5 GHZ RADIO CHANNELS

EQUIP transceivers have two 5 GHz radios that can be set automatically or manually� The default

setting is Auto�
Go to SYSTEM>SETTINGS and select Remote Transceiver from the drop-down list�
Tap on the More icon (the three vertical blue dots) at the end of the transceiver row, see Fig� 17�

Fig. 17

Select "Scan" from the drop-down list to have EQUIP select the optimum 5 GHz channels�

Fig. 18

Tap the "Start Scanning Now" button to begin scanning�

Fig. 19

The outer port LED on the transceiver front will initially flash a different color as the EQP-TCVR

scans for available channels before turning solid green once a channel is found (on the base station

HOME screen, the “Transceivers” indicator is yellow while scanning before turning green)�

Содержание Clear-Com 104G070


















Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды

HME Clear-Com 104G070, Руководство по установке

Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды