HME Clear-Com 104G070 Скачать руководство пользователя страница 5

Страница: 5 / 18

INTRODUCTION AND SYSTEM OVERVIEW

Congratulations and thank you for choosing this Clear-Com product� EQUIP is a wireless intercom

system operating in the ISM 5 GHz frequency band� The system supports up to forty wireless all-in-

one headsets and four transceivers� The transceivers can cover a large area with seamless roam-

ing, approximately 300-500 ft (91-152 m) indoor, and 800-1000 ft (244-305 m) outdoor� The sys-

tem turns on automatically once power is connected to the base station during installation�

Note:

The Base Station User Interface uses a screen saver; if the screen goes black, just tap to wake up�

EQUIP Base Station

Supports Maximum of 4x Transceiver

Category 5/6

Cable length from EQUIP base to TCVR = approx. 500ft.

Protocol is propritary. Not Ethernet

Supports Maximum of 40

All-in-one Headsets

Supports 2 x 4-wire Audio I/O

EQUIP Transceiver

Ch. 1

Ch. 2

Fig. 1

Table 1 provides a list of component part numbers used with the EQUIP system

CC Part Number

Description

G30238-3A1

EQUIP Base Station

PSU-00002

EQUIP Base Station DC power supply

115G408

PSU-00002 Power Cable

G30340-3Z1

EQUIP Transceiver

G30249-2Z1

EQUIP all-in-one 2 CH Headset

104G070

BAT70 Battery

G30317-3Z1

AC70 Battery Charger

PSU-00004

AC70 Charger Power supply DC -US

610022Z

IEC Power Cord (US version)

Table 1

SYSTEM LOG IN

Once EQUIP is installed, it is configured via the Base Station User Interface. A four-digit PIN is

required to log in to the system to configure it or make changes. When you tap on a sidebar menu

option you are prompted to enter a PIN or you can use the LOG IN menu option to enter the PIN�

This PIN is provided by Clear-Com� Record this PIN here:

Содержание Clear-Com 104G070


















Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды

HME Clear-Com 104G070, Руководство по установке

Результаты поиска

Содержание Clear-Com 104G070

Отзывы:

Похожие инструкции для Clear-Com 104G070

Бренды по названию

Популярные бренды