Hitachi WH 12DMR Скачать руководство пользователя страница 36

Страница: 36 / 47

--- 33 ---

(9) Lubrication

(a) ATTOLUB MS No. 2

•

Oil groove and claw of Hammer (D)

[12] <9>

•

8 mm dia. hole of Anvil (F)

[10]

or Anvil (R) Ass'y

<7>

, sliding section between Anvil (F)

[10]

or Anvil (R)

Ass'y

<7>

and the metal, and upper surface of the claw

•

Two Steel Balls D5.556

[11] <8>

•

Pinion tooth flanks of the Armature Ass'y DC 12V

[26] <23>

, tooth flanks of Ring Gear (C)

[21] <18>

tooth flanks of the Idle Gear Set

[19] <16>

•

Metal oil groove of the Hammer Case

[8] <4>

(b) HITACHI MOTOR GREASE No. 29 (WH 12DMR only)

•

Two Steel Balls D3.5

[9]

•

Sliding section between Anvil (F)

[10]

and Guide Sleeve (D)

[4]

•

Cam groove and oil groove of Hammer (D)

[12] <9>

•

Cam groove and sliding section of Spindle (D)

[18] <15>

•

5 mm diameter hole of Idle Gear Set

[19] <16>

•

All around the Needle Roller

[20] <17>

•

Twenty-eight Steel Balls D3.175

[13] <10>

(10) Screw tightening torque

•

Tapping Screw (W/Sp. Washer) D4 x 25 (Black)

[7] <3>

• • •

1.96 0.49 N

•

m (20 5 kgf

•

cm, 17.4 4.3 in-lbs.)

•

Tapping Screw (W/Flange) D4 x 20 (Black)

[33] <30>

• • • • • •

1.96 0.49 N

•

m (20 5 kgf

•

cm, 17.4 4.3 in-lbs.)

•

Machine Screw (W/Washers) M4 x 25

[46] <44>

• • • • • • • • • • • • •

1.27 1.96 N

•

m (13 to 20 kgf

•

cm, 2.6 to 3.5 in-ibs.)

•

Machine Screw (W/Sp. Washer) M3 x 5

[36] <33>

• • • • • • • • • • • •

0.29 to 0.39 N

•

m (3 to 4 kgf

•

cm, 2.6 to 3.5 in-lbs.)

•

Special Screw M5

[48] <46>

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

1.96 0.49 N

•

m (20 5 kgf

•

cm, 17.4 4.3 in-lbs.)

•

Brush cap

[32] <29>

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

0.78 0.10 N

•

m (8 1 kgf

•

cm, 6.9 0.9 in-lbs.)

10-2. Precautions in Disassembly and Reassembly of Battery Charger

Refer to the Technical Data and Service Manual for precautions in disassembly and reassembly of the Model

UC 14YFA or UC 18YG Battery Charger.

Содержание WH 12DMR
















































Результаты поиска

Содержание WH 12DMR

Отзывы:

Бренды по названию

Популярные бренды

Hitachi WH 12DMR, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание WH 12DMR

Отзывы:

Бренды по названию

Популярные бренды