Hitachi WH 12DMR Скачать руководство пользователя

Страница: 23 / 47

--- 20 ---

CAUTION

•

Read thoroughly HANDLING INSTRUCTIONS

before use.

•

Do not disassemble nor throw into fire.

CAUTION

•

Read thoroughly HANDLING INSTRUCTIONS

before use.

CAUTION

(9) Do not attempt to disassemble the storage battery or the charger.

Special devices, such as a thermostat, are built into the storage battery and charger to permit rapid charging.

Incorrect parts replacement and/or wiring will cause malfunctions which could result in fire or other hazards.

Instruct the customer to bring these units to an authorized service center in the event repair or replacement is

necessary.

(10) Disposal of the Type EB 1220BL, EB 1226HL or EB 1230HL Storage Battery

Ensure that all customers understand that Type EB 1220BL, EB 1226HL or EB 1230HL Storage Batteries

should be turned into any Hitachi power tool sales outlet or authorized service center when they are no longer

capable of being recharged or repaired. If thrown into a fire, the batteries may explode, or if discarded

indiscriminately, leakage of the cadmium compound contained in the battery may cause environmental

pollution.

B. Caution Plates

(1) The following precautions are listed on the Name Plate or Caution Plate attached to the main body of each

tool.

For the U.S.A. and Canada

For Oceania

For the U.S.A. (excludes French) or Canada

WARNING

•

To reduce the risk of injury, user must read and

understand Instruction Manual.

AVERTISSEMENT

•

Afin de réduire le risque de blessures, I'utilisateur doit lire

et bien comprendre le mode d'emploi.

(2) The following cautions are listed on the Name Plate attached to each type EB 1220BL, EB 1226HL or

EB 1230HL storage battery.

For Europe

•

For safe operation, see Instruction Manual.

•

Use HITACHI charger recommended in

instruction manual for recharging.

Содержание WH 12DMR
















































Результаты поиска

Содержание WH 12DMR

Отзывы:

Похожие инструкции для WH 12DMR

Бренды по названию

Популярные бренды

Hitachi WH 12DMR, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание WH 12DMR

Отзывы:

Похожие инструкции для WH 12DMR

Бренды по названию

Популярные бренды