Hitachi RAC-10EX9 Скачать руководство пользователя страница 2

– 2 –

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

Pay special attention to signs of “     

Warning

” and “     

Caution

”. The “Warning” section contains matters which,

if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may
result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

The sign indicate the following meanings.

Please keep this manual after reading.

!

SAFETY PRECAUTION

WARNING

PRECAUTIONS DURING INSTALLATION

Do not reconstruct the unit.
Water leakage, fault, short circuit or fire may occur if you reconstruct
the unit by yourself.

Please ask your sales agent or qualified technician for the installation
of your unit. Water leakage, short circuit or fire may occur if you install
the unit by yourself.

Please use earth line.
Do not place the earth line near water or gas pipes, lightning-conductor,
or the earth line of telephone. Improper installation of earth line may
cause electric shock.

A circuit breaker should be installed depending on the mounting site of
the unit. Without a circuit breaker, the danger of electric shock exists.

Do not install near location where there is flammable gas. The outdoor
unit may catch fire if flammable gas leaks around it.

Please ensure smooth flow of water when installing the drain hose.

CAUTION

!

!

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

PRECAUTIONS DURING OPERATION

Avoid an extended period of direct air flow for your health.

W

A
R

N

I

N
G

!

Should abnormal situation arises (like burning smell), please stop operating the unit
and turn off the circuit breaker. Contact your agent. Fault, short circuit or fire may
occur if you continue to operate the unit under abnormal situation.

Please contact your agent for maintenance. Improper self maintenance may cause
electric shock and fire.

Please contact your agent if you need to remove and reinstall the unit. Electric
shock or fire may occur if you remove and reinstall the unit yourself improperly.

Do not put objects like thin rods into the panel of blower and suction side
because the high-speed fan inside may cause danger.

During thunder storm, disconnect and turn off the circuit breaker.

Do not use any conductor as fuse wire, this could cause fatal accident.

!

Make sure to connect earth line.

Indicates the instructions that must be followed.

The sign in the figure indicates prohibition.

W

A
R

N

I

N
G

!

This unit has UV LED which emits ultra violet light.

AVOID DIRECT EYE EXPOSURE.

!

Содержание RAC-10EX9





































Отзывы: