Hitachi P1-00041-H, Основное руководство

Страница: 123 / 131

7-1
Chapter 7
Specifications
Chapter 7 Specifications
7.1 200V class specifications
*1) The rated input current is the value when the drive is operated in the
rated output current. The value of the impedance at the supply side
changes due to the wiring, breaker, input reactor, etc.
*2) Following are for Low Voltage Directive (LVD) compliant.
- Pollution degree 2
- Overvoltage category 3
*3) The power supply capacity is the value of the rated output current at
220V. Impedance at the supply side changes due to the wiring,
breaker, input reactor, etc.
*4) Is necessary to set the carrier frequency settings [bb101]/[bb201]
equal or greater than the (maximum output frequency x 10)Hz. For
induction motor IM, set the carrier frequency to 2 kHz or more
except V/f control. For synchronous motor (SM), permanent magnet
motor (PMM) set the carrier frequency to 8 kHz or more.
*5) The values for the sensorless vector control are assigned according
to the values in the ND rating of the Hitachi standard motor table.
Torque characteristics may vary by the control system and the use of the
motor.
*6) The key height of keypad are exclued from dimensions. When an
option is connected, the dept neccesary is increased. Refer to the each
optional instruction.
Model name(format)
P1-*****-L
00044 00080 00104 00156 00228 00330 00460 00600 00800 00930 01240 01530 01850 02290 02950
ND standard capacity
P1-***L
004 007 015 022 037 055 075 110 150 185 220 300 370 450 550
Applicable motor
capacity
(4 poles)(kW)
VLD 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75
LD 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75
ND 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55
O
u
tp
u
t
Rated output
current(A)
VLD 4.4 8.0 10.4 15.6 22.8 33.0 46.0 60.0 80.0 93.0 124 153 185 229 295
LD
3.7 6.3 9.4 12.0 19.6 30.0 40.0 56.0 73.0 85.0 113 140 169 210 270
ND 3.2 5.0 8.0 11.0 17.5 25.0 32.0 46.0 64.0 76.0 95.0 122 146 182 220
Overload
current rating
VLD 110% 60sec / 120% 3sec
LD 120% 60sec / 150% 3sec
ND
150% 60sec / 200% 3sec
Rated output voltage Three-phase(3 wire)200
～
240V (Corresponding to the incoming voltage)
Rated
capacity
(kVA)
200V
VLD 1.5 2.8 3.6 5.4 7.9 11.4 15.9 20.8 27.7 32.2 43.0 53.0 64.1 79.3 102.2
LD 1.3 2.2 3.3 4.2 6.8 10.4 13.9 19.4 25.3 29.4 39.1 48.5 58.5 72.7 93.5
ND 1.1 1.7 2.8 3.8 6.1 8.7 11.1 15.9 22.2 26.3 32.9 42.3 50.6 63.0 76.2
240V
VLD 1.8 3.3 4.3 6.5 9.5 13.7 19.1 24.9 33.3 38.7 51.5 63.6 76.9 95.2 122.6
LD 1.5 2.6 3.9 5.0 8.1 12.5 16.6 23.3 30.3 35.3 47.0 58.2 70.3 87.3 112.2
ND 1.3 2.1 3.3 4.6 7.3 10.4 13.3 19.1 26.6 31.6 39.5 50.7 60.7 75.7 91.5
In
p
u
t
Rated input
current(A)
*1)
VLD 5.2 9.5 12.4 18.6 27.1 39.3 54.8 71.4 95.2 110.7 147.6 182.1 220.2 272.6 351.2
LD 4.4 7.5 11.2 14.3 23.3 35.7 47.6 66.7 86.9 101.2 134.5 166.7 201.2 250.0 321.4
ND 3.8 6.0 9.5 13.1 20.8 29.8 38.1 54.8 76.2 90.5 113.1 145.2 173.8 216.7 261.9
Rated input
AC voltage
*2)
Control power: Single-phase supply 200
～
240V(+10%, -15%), 50Hz/60Hz(±5%)
Main circuit power supply: Three-phase(3 wire) 200
～
240V(+10%, -15%), 50Hz/60Hz(±5%)
Power supply
capacity
(kVA) *3)
VLD 2.0 3.6 4.7 7.1 10.3 15.0 20.9 27.2 36.3 42.2 56.3 69.4 83.9 103.9 133.8
LD 1.7 2.9 4.3 5.4 8.9 13.6 18.1 25.4 33.1 38.6 51.3 63.5 76.7 95.3 122.5
ND 1.5 2.3 3.6 5.0 7.9 11.3 14.5 20.9 29.0 34.5 43.1 55.3 66.2 82.6 99.8
Carrier frequency
variation
*4)
VLD
0.5
～
10.0kHz
LD
0.5
～
12.0kHz
ND 0.5
～
16.0kHz
Starting torque *5) 200%/0.3Hz
B
ra
k
in
g
Regenerative Internal BRD circuit (external discharge resistor value) External regenerative braking unit
Minimum resistance
value(Ω)
50 50 35 35 35 16 10 10 7.5 7.5 5 - - - -
D
im
e
n
si
o
n
s
*
6
)
H(height)(mm) 255 255 255 255 255 260 260 260 390 390 390 540 550 550 700
W(width)(mm) 150 150 150 150 150 210 210 210 245 245 245 300 390 390 480
D(Depth)(mm) 140 140 140 140 140 170 170 170 190 190 190 195 250 250 250
Protective structure IP20 – UL Open Type
Aprox. weight (kg) 4 4 4 4 4 7 7 7 16 16 16 22 30 30 43