Hitachi HX-RIO3 Series Скачать руководство пользователя страница 14

Страница: 14 / 63

HX-RIO3 Series

4.2.LED Indicator

4.2.1. Module Status LED (MOD)

State

LED is

To indicate

No Power

Off

No power is supplied to the unit.

Device Operational

Green

The unit is operating in normal condition.

Device in Standby

Blinking Green

The EEPROM parameter is not initialized yet.
Serial Number is zero value (0x00000000)

IAP Mode

Toggle Green/Red

IAP Mode : Available for firmware download using Firefox.

Unrecoverable Fault

Red

The unit has occurred unrecoverable fault in self-testing.
- Firmware fault

*The IP address to access IAP web server during IAP Mode : 192.168.100.10 (Recommended to use Firefox)

4.2.2. Network Status LED (NET)

State

LED is

To indicate

Off-line

Off

Network Offline.

On-line (Connect)

Green

On-line Mode and network is connected.

Error

Red

Network Error

Diagnostic

Blinking Red

Diagnostic Mode

* Blinking MOD & NET LED : BOOTP/DHCP is requesting the address data for new IP address.

(You can change the IP setting mode. Please refer to this manual in the part of IP set-up.)

Содержание HX-RIO3 Series
































































Результаты поиска

Содержание HX-RIO3 Series

Отзывы:

Hitachi HX-RIO3 Series, Руководство пользователя, Страница: 14 / 63

Результаты поиска

Содержание HX-RIO3 Series

Отзывы: