Hisun Motors HS 244-2 Скачать руководство пользователя страница 53

Страница: 53 / 65

Periodic Service

10-21

coolant every 2 years.

NOTE:



The above data represent industry

standards that necessitate a minimum glycol

content in the concentrated antifreeze.



When the coolant level drops due to

evaporation, add water only to keep the

antifreeze mixing ratio less than 50%. In

case of leakage, add antifreeze and water in

the specified mixing ratio before filling into

the radiator.

■

Replacing Radiator Hose (Water pipes)

Replace the hoses and clamps.

(See “Checking Radiator Hose and Clamp” in

“EVERY 200 HOURS” in “PERIODIC SERVICE”

section.)

■

Replacing Fuel Hose

Consult your local HUANSONG Dealer for this

service.

■

Replacing Brake Master Cylinder (Inner

parts)

Consult your local dealer for this service.

■

Replacing Front Brake Seal

Consult your local dealer for this service.

■

Replacing Rear Brake Cylinder Seal

Consult your local dealer for this service.

■

Replacing Intake Air Line

Consult your local dealer for this service.

EVERY 4 YEARS

■

Replacing Brake Hose

Consult your local Dealer for this service.

■

Replacing Slow-Blow Fuses

The slow-blow fuses are intended to protect the

electrical cabling. If any of them have blown out,

be sure to pinpoint the cause.

◆

Replacing procedure

1) Disconnect the negative cable of the battery.

2) Open the slow-blow fuse box cover.

3) Pull out the slow-blow fuse.

4) Insert a new slow-blow fuse into the box.

5) Close the slow-blow fuse box cover.

6) Connect the negative battery cable.

①

Slow-blow fuse box cover

■

Replacing Light Bulb



Head

lights

Take the bulb out of the light body and

replace it with a new one.



Other

lights

Detach the lens and replace the bulb

Light Capacity

Head lights

2x55W

Tail light

LED 0.5W

Brake light

LED 1W

Instrument panel light

Содержание HS 244-2


































































Результаты поиска

Содержание HS 244-2

Отзывы:

Похожие инструкции для HS 244-2

Бренды по названию

Популярные бренды

Hisun Motors HS 244-2, Руководство по введению

Результаты поиска

Содержание HS 244-2

Отзывы:

Похожие инструкции для HS 244-2

Бренды по названию

Популярные бренды