manualshive.com logo in svg

Hirschmann MACH 1040 Series, Руководство пользователя

Поделиться
Скачать
Hirschmann MACH 1040 Series Скачать руководство пользователя страница 65

Spanning Tree

Redundancy L2B

Release 6.0 07/2010

4.6 The Rapid Spanning Tree 

Protocol

65

Parameter

Meaning

Possible Values

Default Setting

STP active

Here you can switch Spanning Tree 
on or off for this port. If Spanning 
Tree is activated globally and 
switched off at one port, this port 
does not send STP-BPDUs and 
drops any STP-BPDUs received.

Note: 

If you want to use other 

layer 2 redundancy protocols such 
as HIPER-Ring or Ring/Network 
coupling in parallel with Spanning 
Tree, make sure you switch off the 
ports participating in these protocols 
in this dialog for Spanning Tree. 
Otherwise the redundancy can fail 
or loops can result.

On

, 

Off

On

Port status (read 
only)

Displays the STP port status with 
regard to the global MSTI (IST).

discarding

,  

learning

, 

forwarding

, 

disabled

, 

manualForwarding

,  

notParticipate

-

Port priority

Here you enter the port priority (the 
four highest bits of the port ID) with 
regard to the global MSTI (IST) as a 
decimal number of the highest byte 
of the port ID.

16 

≤

 n·16 

≤

 240

128

Port path costs Enter the path costs with regard to 

the global MSTI (IST) to indicate 
preference for redundant paths. If 
the value is 0, the Switch 
automatically calculates the path 
costs for the global MSTI (IST) 
depending on the transmission rate.

0 - 200,000,000

0 (automatically)

Table 9: Port-related RSTP settings and displays

Содержание MACH 1040 Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды