Hirschmann MACH 1040 Series Скачать руководство пользователя страница 37

Страница: 37 / 78

Multiple Rings

Redundancy L2B

Release 6.0 07/2010

3.1 Sub-Ring

When you have configured both SRMs and, if applicable, the devices
included in the Sub-Ring, close theSub-Ring’s redundant line.

enable

Switch to the Privileged EXEC mode.

configure

Switch to the Configuration mode.

sub-ring 1 operation enable

Switches on the Sub-Ring with the Sub-Ring ID 1.

Operation set to Enabled
exit

Switch to the privileged EXEC mode.

show sub-ring

Displays the state for all Sub-Rings on this
device.

Ring ID: 1

Mode of Switch (administrative setting)... manager

Mode of Switch (real operating state)..... manager

Port Number............................... 1/9, State: Forwarding

Protocol...................................Standard MRP

MRP Domain ID..................................
255.255.255.255.255.255.255.255.255.255.255.255.255.255.255.255Ri
ng Name...................................... Test

Partner MAC.................................... 02:E3:00:1B:00:09

VLAN ID........................................ 0 (No VLAN)

Operation...................................... Enabled

General Operating States:

SRM Setup Info (Config. Failure)............... No Error

Manager-related Operating States:

Ring State..................................... Open

Redundancy Guaranteed.......................... No
copy system:running-config

nvram:startup-config

Save the current configuration to the non-volatile
memory.

Содержание MACH 1040 Series















































































Результаты поиска

Содержание MACH 1040 Series

Отзывы:

Бренды по названию

Популярные бренды

Hirschmann MACH 1040 Series, Руководство пользователя

Результаты поиска

Содержание MACH 1040 Series

Отзывы:

Бренды по названию

Популярные бренды