background image

System 2000 AUTO TEMP

1

System 2000 Auto Temp

1. Specifications

Model:

ACT-12 -- Staged on/off controller with 7 temperature inputs and 13 relay outputs

Electrical Ratings

Voltage Input -- 120 VAC (240VAC available) 50/60 Hz.
Power Consumption -- 20 VA Max.

Contact Ratings:

1/10 HP Inductive @ 120VAC
2 Amp @ 12VAC Resistive

Sensors:

Negative Temperature Coefficient Thermistor type. Maximum 1000 ft distance from sensor to controller.
Software calibration capability in controller.

Temperature Range:

-20.0F to 120.0F all targets settable in same range in 1F increments.

2. Limited Warranty

All products are warranted to be free from defects in material and workmanship for a
period of one year from the date of purchase if installed and used in strict accordance with
the installation instructions. Liability is limited to the sale price of any products proved to
be defective or, at manufacturers option, to the replacement of such products upon their
return. No products are to be returned to the manufacturer, until there is an inspection
and/or a return-goods authorization (RGA) number is issued.
All complaints should be directed first to the authorized distributor who sold the product.
If satisfaction is not obtained or the name of the distributor is not known, write the
manufacturer that appears below, directed to the attention of Customer Service Manager.
This limited warranty is expressly in lieu of any and all representations and warranties
expressed or implied, including any implied warranty of merchantability or fitness for a
particular purpose. The remedy set forth in this limited warranty shall be the exclusive
remedy available to any person. No person has authority to bind the manufacturer to any
representation or warranty other than this limited warranty. The manufacturer shall not be
liable for any consequential damages resulting from the use of our products or caused by
any defect, failure or malfunction of our products. (Some areas do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.)
This warranty gives you specific legal rights and you may also have other rights that vary
from area to area.

Warrantor:

Hired-Hand, Inc.
1733 Co. Rd. 68
PO Box 99
Bremen, AL  35033

Содержание System 2000 AUTO TEMP











Отзывы: