Hioki TS2400 Скачать руководство пользователя страница 9

Страница: 9 / 116

Usage Notes

Usage Notes

Follow these precautions to ensure safe operation and to obtain the full benefits of the various

functions. Ensure that your use of the instrument falls within the specifications not only of the

instrument itself, but also of any accessories, options and other equipment being used.

Before using the instrument for the first time

Upon delivery, check that the main unit and all necessary accessories are included in the package.

Furthermore, check that the main unit, accessories, panel switches, and terminals are all

functioning normally and that none is faulty or damaged.

WARNING

If any item is faulty or damaged, do not use the instrument in its present state.

Contact your authorized Hioki distributor or reseller.

Inspection

Before using the instrument each time, verify that it operates normally to ensure that there is no

damage.

If you find any damage, contact your authorized Hioki distributor or reseller.

WARNING

•

Tape switches are installed around the moving parts of the model Z5016 WPT

Testing Platform so that any unsafe contact is detected and the testing platform

is stopped. In addition, EMERGENCY STOP buttons are installed on the front

side and the pendant unit of the model Z5017 PLC Rack. Prior to using this

instrument, check the following. If the operation of the instrument is different

from the description below, turn off the main breaker on the front side of the

Z5017 PLC Rack and contact your authorized Hioki distributor or reseller.

1. The

[EMERGENCY STOP]

indicator lights up when something comes in

contact with the tape switches and the EMERGENCY STOP button is

pressed.

2. When the

[READY]

button is pressed when the

[EMERGENCY STOP]

indicator

lit, the instrument does not start up.

•

Always turn off the main breaker before lubricating the axis guide and ball

screw units.

Operating environment

WARNING

Installing the instrument in inappropriate locations may cause a malfunction of

instrument or may give rise to an accident. Avoid the following locations:

•

Exposed to direct sunlight or high temperature

•

Exposed to corrosive or combustible gases

•

Susceptible to vibration

•

Exposed to water, oil, chemicals, or solvents

•

Exposed to high humidity or condensation

•

Exposed to high quantities of dust particles

Содержание TS2400





















































































































Результаты поиска

Содержание TS2400

Отзывы:

Hioki TS2400, Инструкция по эксплуатации, Страница: 9 / 116

Результаты поиска

Содержание TS2400

Отзывы: