Hino J08EVB Скачать руководство пользователя страница 10

Страница: 10 / 11

www.DieselDocs.com

−

When installing the piston rings on the piston, ensure that the piston skirt is at the

bottom, and use the special tool.

NOTICE:

Install the piston rings in order shown in the figure.

6. Assemble the Piston and Connecting Rod.

NOTICE:

Warm up the piston first in hot water, to 80-90



C {176-194



F}, for approximately 5

minutes.

−

Install the retainer ring at one end of the piston pin holes.

−

Apply engine oil to the piston pin.

−

Fix the piston and connecting rod by inserting the pin.

−

Fit the new retainer ring at the other end.

7. Install the Cylinder Liner and Cylinder Head.

NOTICE:

Do not twist the O-ring when installing it on the cylinder liner and cylinder head.

−

Rotate the crankshaft to the top dead center position.

−

Arrange the piston rings so that their gaps are equally spaced.

−

Install the cylinder liner and cylinder head.

Содержание J08EVB












Результаты поиска

Содержание J08EVB

Отзывы:

Бренды по названию

Популярные бренды

Hino J08EVB, Руководство пользователя

Результаты поиска

Содержание J08EVB

Отзывы:

Бренды по названию

Популярные бренды