background image

Installation Instructions for:

105295-HEI Kit 

Gen1 to Gen5 

Control System

S

PEED

 T

UNING

How to Adjust the 
Slow Drive Speed – GR Models

1.

Pull out the red Emergency Stop button to the on 
position at the ground controls.

2.

Push in the red Emergency Stop button to the off 
position at the platform controls.

3.

Turn the key switch to platform controls.

4.

At the platform controls, press and hold the lift 
function select and horn buttons and pull out the 
red Emergency Stop button to the on position. 

Outcome: The diagnostic display will show “PS”. 

5.

Release the lift function select and horn buttons.

Outcome: The diagnostic display, at the platform 
controls and the ECM, will show the maximum lift 
speed percentage.

6.

Press and hold the slow speed select button. 

Outcome: The diagnostic display will show the 
slow drive speed percentage.

7.

Use the steering thumb rocker switch on the 
joystick to increase or decrease the slow drive 
speed percentage. Refer to Section 2, 
Specifications, in the appropriate Service Manual 
for function speeds.

8.

Turn the key switch to the off position.

Note: Any change in software settings will not take
effect until the key switch is turned to the off 
position.

   a

Joystick Controller with Thumb  Steering 
Rocker 

   b

Horn Button

   c

Lift Function Select Button 

   d

Red Emergency Stop Button 

   e

Drive Function Select Button 

P/N 105294-HEI Rev.0

HEI

 16/ 16

Содержание 105295-HEI

















Отзывы: