![background image](http://html1.mh-extra.com/html/hilti/wsc-85/wsc-85_operating-instructions-manual_2136432015.webp)
4.1 Procedure if the extraction adapter is
blocked
1. Disconnect the supply cord plug from the
power outlet.
2. Clean out the extraction adapter.
3. Check for misalignment or binding of
moving parts, breakage of parts and any
other condition that may affect the power
tool’s operation.
5. Using the saw
■
Always disconnect the supply cord plug
from the mains socket before making any
adjustments to the machine.
Sawing along a line
Rest the front part of the baseplate on the
workpiece, switch on the machine and push
the circular saw forward evenly in the
direction of the cut.
The baseplate is equipped with four cutting
line indicators
4
for 0°, 22.5°, 45° and 60°.
The edge of the cutting line indicator
corresponds with the inside edge of the saw
blade.
Sawing using the parallel guide (Fig. 4)
The parallel guide
5
permits precise cuts to be
made parallel to the edge of a workpiece or,
respectively, permits strips of equal width to
be cut. To adjust the cutting width, release the
clamping screw
3,
adjust the guide to the
required position and then re-tighten the
clamping screw
3
. The parallel guide can be
mounted on either side of the baseplate in the
same way.
The parallel guide may be fitted in the reverse
position (with the guide pointing upwards). In
13
2. Correct use
The machine is designed for cutting soft-
wood, hardwood, plywood, plastics and other
similar materials. It must
not
be used to cut
metals. The user of the machine is liable for any
damage caused by misuse, e.g. carrrying the
machine by the supply cord, pulling the plug out
of the socket by pulling on the supply cord, use
of the wrong saw blades etc. The list of safety
precautions and generally accepted accident
prevention regulations for working with elec-
tric tools must be observed.
3. Operation
Before operation
Before switching on the machine, check to
ensure that the saw blade runs true and ro-
tates freely, and that the riving knife is cor-
rectly adjusted.
■
Caution! Disconnect the supply cord plug
from the mains socket before adjusting the
riving knife. The thickness of the riving knife
must be less than the cutting width of the
saw blade and greater than or equal to the
thickness of the blade’s steel disc.
For safety reasons, the riving knife must always
be used. The riving knife is designed to prevent
jamming/sticking of the saw blade. It should be
adjusted while cutting depth is set at maximum.
Loosen the fastening screws
14
, adjust the riv-
ing knife
9
(fig. 5) and then retighten the screws
14
.
■
Remove any adjusting tools or wrench-
es etc. before starting the machine.
Operation
■
Hold the machine securely and maintain
a secure stance.
■
Put the machine down only after the piv-
oting guard has closed.
The mains supply voltage must correspond with
the information printed on the rating plate.
Switching the machine ON/OFF
■
Caution! Do not switch on the machine
while the blade is in contact with the work-
piece.
Switching on:
Press the switch-on interlock
17
and the ON switch
18
simultaneously.
Switching off:
Release the ON switch
18
.
The circular saw is equipped with an automat-
ic saw blade brake. The braking procedure be-
gins immediately after releasing the ON/OFF
switch
18,
causing the saw blade to come to
a standstill.
Protecting the saw blade
■
Protect the circular saw blade from damage.
■
Never lay the circular saw blade down on
hard materials. The carbide-tipped teeth could
suffer damage.
Changing the saw blade (Fig. 3)
■
Caution! Disconnect the supply cord
plug from the mains socket before
changing the saw blade.
Lay the machine down on the supporting ribs
at the motor end. When changing a saw blade,
prevent rotation of the motor spindle by using
one hand to press the spindle lockbutton
10
.
Removing the saw blade (Fig. 5)
The hex. socket wrench required for releas-
ing the flange screw is located beneath the
motor endcap. Adjust the saw to a cutting
depth of 0 by way of the cutting depth adjust-
ing lever
1
. Use the hex. socket wrench
19
to
unscrew the screw
11
in a counter-clockwise
direction and remove the clamping flange
12
(fig. 3). Swing back the pivoting guard
13
, hold
it securely in place and remove the saw blade.
Fitting the saw blade (Fig. 3/5)
Note the correct direction of rotation when
fitting the saw blade. The teeth and the arrow
printed on the saw blade must point in the
direction of the arrow on the upper part of the
blade guard. Clean wood chips and other dirt
or dust etc. from the surfaces and check that
the inner clamping flange
12
is correctly
seated. Fit the clamping flange
12
and then
insert and tighten the screw
11
.
■
Check the data for the saw blade to en-
sure that it matches the data for the machine.
4. Dust extraction
Use of a dust extraction system improves saw
dust removal performance, reduces the amount
of dust in the surrounding atmosphere and pre-
vents saw dust being spread over a wide area.
Connect the external extraction system when
you intend to work with the saw over a long pe-
riod or when materials that produce hazardous
dust are to be cut.
The extraction adapter
15
should only be left in
place on the machine when an external ex-
traction system is in use. The exit opening may
otherwise become blocked, especially when
cutting damp wood. Fit the extraction adapter
from the front, with the opening facing the rear
of the machine, and insert it into the dovetail
socket until it clicks into place. The extraction
system will be attached securely only when the
connector has been felt to click into place.
■
Observe the accident prevention regulations.
Printed: 08.07.2013 | Doc-Nr: PUB / 5071333 / 000 / 01