unit at locations where there may be a risk of it falling
(e.g. on scaffolding). The electric extension cable and
its plugs and sockets must not be allowed to lie in water.
Do not use the equipment in the vicinity of inflammable
liquids or gases. Make provision for water removal and
disposal.
■
Always keep the operating instructions with the equip-
ment and pass them on to any subsequent user who has
been trained in its use.
■
When not in use, store the hydraulic saw system in
a locked, dry place out of reach of children.
■
Use the hydraulic saw system only for the applica-
tions for which it has been designed.
■
In addition to carrying out the specified care and main-
tenance, careful cleaning is also a prerequisite for safe,
trouble-free operation of the equipment.
■
Always stay alert and carefully observe the progress
of your work. Proceed logically and do not use the equip-
ment when you are unable to concentrate on your work.
■
Do not leave tools (e.g. open-end wrenches) in place
on the equipment. Check the drive unit to ensure that all
tools have been removed before switching on.
■
Keep the working area tidy and well lit. An untidy
workplace and inadequate lighting increases the risk of
accident.
■
Wear suitable, close-fitting work clothes including a
hard hat, protective goggles, protective gloves, safety
footwear, ear protectors and a hair net, if you have long
hair.
■
Respiratory protection should be worn when work-
ing in enclosed or poorly ventilated areas and when dry
cutting is being carried out.
■
Keep children and other persons well away from the
workplace and allow no-one to touch the wall saw or
power cable.
■
Failure to comply with the warnings and safety infor-
mation may lead to severe or possibly fatal injury as
well as serious damage to the equipment and other
property.
■
Dust from material such as paint containing lead,
some wood species, minerals and metal may be harm-
ful. Contact with or inhalation of the dust may cause all-
22
5. Safety precautions
General safety information
■
Sawing work influences the statics of the structure.
Approval must be obtained from the site engineer or
architect prior to carrying out drilling and sawing work.
■
You must be fully aware that working with the
D-LP 32 / DS-TS 32 hydraulic saw system always involves
a certain element of risk due to wear or damage to parts.
Check the condition of the entire system, including acces-
sories, each time before use to ensure it functions cor-
rectly.
Wearing parts such as the blade guard holder rubber,
end stop, blade mounting screw, flush-cutting blade
mounting screws, etc., should be inspected particular-
ly carefully. Check that all parts have been assembled
correctly and consider all other factors that could influ-
ence operation of the equipment.
Contact your Hilti representative or Hilti service centre
if faults or deficiencies are found.
■
Use the hydraulic saw system only when you have
read the operating instructions, when you are familiar
with the information contained therein and when you
have been trained to use the equipment safely by a Hilti
specialist. All warnings and safety information must be
observed.
■
The area in front of, behind or below the surface where
sawing work or drilling work is to be carried out must
be secured in such a way that persons or equipment can-
not be injured or damaged by falling objects. If neces-
sary, concrete cores or blocks of concrete that have been
cut free should be secured to prevent them falling.
■
The operator in charge must be aware of the possi-
ble dangers and of his responsibility for safety, both with
regard to himself and to others.
■
Read the operating instructions carefully before oper-
ating the equipment for the first time and observe all pre-
cautions and instructions contained therein.
■
The influences of the environment in which you are
working must be taken into account. Do not position the
equipment where the hydraulic unit is liable to become
very wet. The hydraulic unit must be kept level during
operation, i.e. on a horizontal surface. Secure the hydraulic
5.1
Printed: 08.07.2013 | Doc-Nr: PUB / 5069667 / 000 / 01
Содержание D-LP 32
