manualshive.com logo in svg

Hill-Rom Centrella Smart+, Руководство по продукции

Поделиться
Скачать
Hill-Rom Centrella Smart+ Скачать руководство пользователя страница 18

18

©2017 Hill-Rom Services, Inc. ALL RIGHTS RESERVED. 
205278 rev 2  13-SEP-2017  ENG – US

Brake & Steer Controls

The brake and steer controls include brake pedals above the foot-end casters 
and brake and steer pedals above the head-end casters. There are three 
positions — steer, neutral and brake.

Steer Position

To activate steer, step down on the green head-end pedal or lift up on the 
orange foot-end pedal. Steer allows for straight travel down long hallways, 
especially when equipped with the optional 5th wheel.

Neutral Position

To move the bed in any direction, move the pedal to the level position. This 
position helps with sideways movements in a room or a small enclosed area, 
or helps align the bed with another surface for patient transfers.

Brake Position

To prevent the bed from moving, step down on the orange brake pedal until 
it is in the full downward position. Unless transporting a patient, always set 
the brakes when the bed is occupied.
If equipped with verbal safety prompts, when you release the brake, 
the “Brake Not Set” will sound when the bed is connected to power, the 
indicator on the upper siderail panel will flash, and a message appears on 
the touchscreen.

Preparing for Transport

1.  Raise all four siderails to the up and locked position.

NOTE: A fully-charged battery for back-up frame controls is preferred. 
If the bed battery is low, put the bed into the desired transport position 
before unplugging the bed from power.

2.  If necessary, shorten the length of the bed to get into elevators, and 

adjust the head section to make sure your view is not obstructed.

3.  Unplug and secure all power cords, hoses and equipment that are to be 

transported with the bed.
NOTE: If the Patient Helper, Experience POD™ device, or IV poles are 
installed, make sure they will not impact doorways or ceiling fixtures.

4.  If the bed has push handles, lift the handles up, and lock them in position. 

Otherwise, use the push handles built-in to the headboard.

5.  Activate Steer by stepping down on the Green pedal.
For beds without IntelliDrive® Powered Transport, continue to transport 
the patient per your facility’s protocol.
For beds with IntelliDrive® Powered Transport, refer to the “Transporting 
with IntelliDrive® Powered Transport” section.

T R ANSP O R T

No

Set Brake

or

unplug bed

to transport.

Brake Not Set

Содержание Centrella Smart+































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды