background image

 

 

disposed of as unsorted municipal waste in the European 
Union. See the product documentation for specific 
battery information. The battery is marked with this 
symbol, which may include lettering to indicate cadmium 
(Cd), lead (Pb), or mercury (Hg). For proper recycling, 
return the battery to your supplier or to a designated 
collection point. For more information see: 
www.recyclethis.info. 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) 
standards requirements. 
 

Safety Instruction 

These instructions are intended to ensure that user can 
use the product correctly to avoid danger or property 
loss.   
The precaution measure is divided into “Warnings” and 
“Cautions” 

Warnings: 

Serious injury or death may occur if any of the 

warnings are neglected. 

Cautions:

 Injury or equipment damage may occur if any 

of the cautions are neglected. 

 

Warnings

 

 

In the use of the product, you must be in strict 
compliance with the electrical safety regulations of 
the nation and region. 

 

Refer to technical specifications for detailed 
information. 

 

Input voltage should meet both the SELV (Safety Extra 
Low Voltage) and the Limited Power Source with AC 
24V or DC 12V according to the IEC60950-1 standard. 
Refer to technical specifications for detailed 
information. 

 

Do not connect several devices to one power adapter 
as adapter overload may cause over-heating or a fire 
hazard. 

 

Make sure that the plug is firmly connected to the 
power socket. 

 

When the product is mounted on wall or ceiling, the 
device shall be firmly fixed.   

 

 

Warnings

 Follow 

these safeguards to 
prevent serious injury 
or death. 

Cautions 

Follow these 

precautions to prevent 
potential injury or 
material damage.   

Содержание UD02783B














Отзывы: