HIKVISION DS-7104NI-K1 Скачать руководство пользователя страница 84

Страница: 84 / 98

8. Click OK.

Note

Up to 8 TB storage capacity is allowed for each network disk.

Result
The added network disks will be displayed in the storage device list.

6.5.4 Configure Storage Mode

Configure HDD Groups

Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a

particular HDD group through HDD settings.
Steps

1. Go to Configuration → Record → Storage Mode .

2. Select Mode as Group.

3. Select a group number.

4. Select IP cameras to record on the HDD group.

Figure 6-26 Group

5. Click Apply.

6. Restart the video recorder to activate the new storage mode settings.

7. After restart, go to Configuration → Record → Storage .

8. Click of desired HDD to set the group.

9. Select a group number for the current HDD.

10. Click OK.

Note

Regroup the cameras for HDD if the HDD group number is changed.

Configure HDD Quota

Each camera can be configured with an allocated quota for storing videos.

Network Video Recorder

Содержание DS-7104NI-K1



































































































Результаты поиска

Содержание DS-7104NI-K1

Отзывы:

Бренды по названию

Популярные бренды

HIKVISION DS-7104NI-K1, Руководство пользователя

Результаты поиска

Содержание DS-7104NI-K1

Отзывы:

Бренды по названию

Популярные бренды