HIKOKI D 6SH, Инструкция по эксплуатации

Страница: 8 / 48

English
8
CAUTION
A stopper assembly is not attached to products equipped
with a keyless chuck because the stopper rod would
come into contact with the keyless chuck.
A stopper assembly should never be mounted on any
product equipped with a keyless chuck in disregard of
the above warning because such action could result in a
serious accident.
6. Caution immediately after use
Immediately after use, if the Drill is still revolving and it
is placed on a location where considerable ground chips
and dust have accumulated, dust may occasionally be
absorbed into the Drill mechanism.
Always pay attention to this possibility.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch power OFF and disconnect the plug from
the receptacle during maintenance and inspection.
1. Inspecting the drill bit
Since use of an abraded drill bit will cause motor
malfunctioning and degraded e ffi ciency, replace the drill
bit with a new one or resharpening without delay when
abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loosened, retighten them immediately, Failure to do so
could result in serious hazard.
3. Servicing
Consult an authorized Service Center in the event of
power tool failure.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci fi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or normal
wear and tear. In case of complaint, please send the Power
Tool, undismantled, with the GUARANTEE CERTIFICATE
found at the end of this Handling instruction, to a HiKOKI
Authorized Service Center.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance with
the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may
not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black. The wire coloured
brown must be connected to the terminal marked with the
letter L or coloured red. Neither core must be connected to
the each terminal.
NOTE
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 87 dB (A)
Measured A-weighted sound pressure level: 76 dB (A)
Uncertainty KpA: 3 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration value
does not exceed 2.5 m/s
2
.
The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of
exposure.
WARNING
○ The vibration and noise emission during actual use
of the power tool can di ff er from the declared total
value depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
○ Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o ff and when it is running idle in addition to the
trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to change
without prior notice.
00Book̲D6SH̲WE̲Gre.indb 8 00Book̲D6SH̲WE̲Gre.indb 8 2021/02/01 15:56:17 2021/02/01 15:56:17