background image

INSTALLATION GUIDE

hidglobal.com

An ASSA ABLOY Group brand

© 2012 - 2018 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID GLOBAL, HID, the HID Brick logo, the Chain Design, and PIVCLASS are trademarks or registered 

trademarks of HID Global, ASSA ABLOY AB, or its affiliate(s) in the U.S. and other countries and may not be used without permission. All other trademarks, service marks, and 

product or service names are trademarks or registered trademarks of their respective owners. 

This Installation Guide is for informational purposes only. HID makes no warranties, expressed or implied, in this summary. Company, product names and data used in sample output 

are fictitious. Specifications are subject to change without notice.

pivCLASS

  R10-H, RP10-H, R40-H, RP40-H, RK40-H, RPK40-H, RKCL40-P, 

RPKCL40-P, RKCLB40-P

Reconfigure Reader Assembly

The following steps reconfigure the reader assembly to position  

   the Contact reader component on the left side of the assembly.

1.  Disassemble the reader.

• Remove the Keypad reader from the backplate
• Carefully unplug the ribbon cable from the module in the  

   back of the Keypad reader. Caution: Do not pull on the ribbon  

   cable as this may damage the connection to the connector.
• Remove the Contact reader from the backplate
• Gently pull the ribbon cable through the backplate 

2.  Reassemble with the Contact reader on the left side of the assembly.

• Rotate the backplate so that the large cutout for the power cable is on the left
• Gently route the ribbon cable back through the backplate slots, as shown below
• Plug the ribbon cable back into the module (back of Keypad reader) and ensure module is fully  

   seated into the reader
• Attach the Contact reader to the backplate (this must be installed first, as the Keypad Reader will fit  

  slightly over the Contact reader)
• Attach the Keypad reader to the backplate (power cable must be threaded through the large  

  square cutout on the backplate)
• Return to Section 2

Contact reader 

Keypad reader 

Backplate

Ribbon cable

Keypad reader

Contact reader 

Backplate

Ribbon cable

Contact reader 

Keypad reader 

Содержание pivCLASS R10-H









Отзывы: