background image

MaxiProx

® 

Installation Guide

  

Part No. 5375-901, Rev E.1 

March 2012 

 

Page 3 of 19 

© 2008-2012 HID Global Corporation.  All rights reserved. 

List of Tables 

Table 1:  TB1 Connector Definition ................................................................................................................................ 7

 

Table 2:  TB2 Connector Definition ................................................................................................................................ 7

 

Table 3:  DIP Switch and Jumper Settings ..................................................................................................................... 7

 

Table 4:  Interface Jumpers Description - P3 and P4 ..................................................................................................... 7

 

Table 5:  Switch Description - SW2 ................................................................................................................................ 8

 

Table 6:  Mode Chart ..................................................................................................................................................... 8

 

Table 7:  Baud Rate Chart – RS232 and RS422 ............................................................................................................ 8

 

Table 8:  Switch Description - SW5 ................................................................................................................................ 8

 

Table 9:  Logic Levels .................................................................................................................................................. 15

 

Table 10:  Data Pulses - Timing Parameters ............................................................................................................... 15

 

Table 11:  Data Timing - Timing Chart ......................................................................................................................... 17

 

 

HID GLOBAL, HID, the HID logo and MaxiProx are the trademarks or registered trademarks of HID Global 
Corporation, or its licensors, in the U.S. and other countries. 

Contact 

If you have questions or comments about MaxiProx, please contact us. 

North America 

15370 Barranca Parkway 

Irvine, CA 92618 

USA 

Phone: 

800 237 7769 

Fax: 

949 732 2120 

Europe, Middle East and Africa 

Phoenix Road 

Haverhill, Suffolk CB9 7AE 

England 

Phone: 

+44 1440 714 850 

Fax: 

+44 1440 714 840 

Asia Pacific 

19/F 625 King’s Road 

North Point, Island East 

Hong Kong 

Phone: 

852 3160 9800 

Fax: 

852 3160 4809 

support.hidglobal.com 

 

Содержание MaxiProx DFM Reader - 5375




















Отзывы: