HID MaxiProx DFM Reader - 5375 Скачать руководство пользователя | Manualshive

Страница: 11 / 19

background image

MaxiProx

®

Installation Guide

Part No. 5375-901, Rev E.1

March 2012

Page 11 of 19

© 2008-2012 HID Global Corporation. All rights reserved.

2.16

Install Cover

Replace the top cover and top cover screw. Make sure that the Auto-tune indicator LED remains in a
steady green state. If the LED is red, remove the cover and re-mount the unit using a non-metallic
spacer to position it further away from the mounting surface. Reinstall the cover, verify Auto-tune, and
install the front label over the top cover screw and the Auto-tune indicator lens.

11.800

+/ - .03

Figure 1: MaxiProx Front View

«
...
9
10
11
12
13
...
»

Содержание MaxiProx DFM Reader - 5375




















Отзывы:

Нет отзывов

Похожие инструкции для MaxiProx DFM Reader - 5375

Бренд: Magnat Audio Страницы: 64

Бренд: JFSound Страницы: 52

Pocketbook Basic 611

Бренд: Obreey Страницы: 64

Бренд: CAB Страницы: 10

Бренд: Cables to Go Страницы: 21

PARALLAX TCS230-DB

Бренд: TAOS Страницы: 2

Бренд: hillvert Страницы: 5

Бренд: StarTech.com Страницы: 3

Бренд: Nav TV Страницы: 22

Бренд: ACS Страницы: 7

Бренд: Boss Audio Systems Страницы: 21

Бренд: Nokia Страницы: 6

Бренд: Nokia Страницы: 30

Бренд: LG Страницы: 72

Бренд: LG Страницы: 178

Accord Sedan 2021

Бренд: Honda Страницы: 14

Бренд: Crutchfield Страницы: 3

Бренд: StarTech.com Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды