HI GrainSaver U-Trough PS-001 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 36

HI GrainSaver U-Trough PS-001 Скачать руководство пользователя страница 6

2.3. Rotating Flighting Safety

• KEEP AWAY from rotating flighting.

• DO NOT remove or modify flighting guards, doors, or covers. Keep in

good working order. Have replaced if damaged.

• DO NOT operate the bin unload without all guards, doors, and covers in

place.

• NEVER touch the flighting. Use a stick or other tool to remove an ob

-

struction or clean out.

• Shut off and lock out power to adjust, service, or clean.

2.4. Rotating Parts Safety

• Keep body, hair, and clothing away from rotating pulleys, belts, chains,

and sprockets.

• Do not operate with any guard removed or modified. Keep guards in good

working order.

• Shut off and remove key or lock out power source before inspecting or

servicing machine.

2.5. Work Area Safety

• Have another trained person nearby who can shut down the bin unload in case of accident.

• The work area should be kept clear of bystanders.

• Keep the work area clean and free of debris.

2.6. Guards Safety

• Keep guards in place and do not operate unless all guards are in place.

• Do not walk on, step on, or damage guards.

• Lock out power before removing a guard.

• Ensure all guards are replaced after performing maintenance.

2.7. Bin Unloading Safety

• Never enter a bin when loading or unloading.

• Unload only as described in the operation section of this manual.

• Lock the bin door (where equipped) and close/lock all other access doors when not in use.

6

«
...
4
5
6
7
8
...
»

Содержание GrainSaver U-Trough PS-001





































Отзывы:

Нет отзывов